Skip to content
LarchHVAC & Appliance · Bellingham (360) 525-9166 Book a visit

Sedro-Woolley · ice makers

Ice Maker Repair in Sedro-Woolley, WA

Ice maker repair in Sedro-Woolley

Most Sedro-Woolley ice makers fail for one of a few reasons: a water line that froze or kinked, a valve screen full of well sediment, or a worn module. We find which, price it in writing and fix it once you approve.

Common cause
Inlet valve screen clogged by sediment in well-fed homes.
Line routes
Crawlspaces and exterior walls in older homes can freeze.
Drive
About 30–38 minutes from downtown Bellingham via I-5 and SR 20.
French-door refrigerator open for a repair check
  • Fee named up fronton the phone, before anyone drives out
  • A price on papersigned off by you before parts come off
  • Border to the SkagitGlacier and Sumas on the same terms as town
  • Seven days, 8 to 7a morning call often means a visit today

An ice maker is the most water-sensitive part of a refrigerator, and Sedro-Woolley gives it plenty to cope with. Homes up SR 9 draw well water that can carry sediment; older homes in town route the supply line through crawlspaces and exterior walls that get cold in winter; manufactured homes often run a long plastic line under the floor to reach the kitchen. Any one of those can starve the ice maker of water, and the result is small cubes, hollow cubes or an empty bin. In older farmhouses the line is sometimes a copper tube put in decades ago, fed by a saddle valve that has corroded half shut.

We trace the problem from the shutoff valve to the bin: supply line, filter, inlet valve, fill tube, ice maker module and dispenser. We carry common valves and ice maker modules for Whirlpool, GE, Frigidaire, LG, KitchenAid and Maytag refrigerators, so many repairs are finished on the first visit. If the fridge itself has a problem, such as a freezer too warm to make ice, we diagnose that as part of the same visit rather than replacing an ice maker that was never at fault. Door dispensers get the same attention: a jammed chute or a grinding auger is often ice that melted and refroze rather than a failed motor.

Ice maker trouble in Sedro-Woolley

  1. You noticeIce slows down, then stops during a cold snap

    Usual sourceSupply line frozen in a crawlspace or exterior wall

    Our repairLocate the frozen section, let it thaw safely and suggest a better route or insulation

  2. You noticeCubes small, cloudy or gritty

    Usual sourceSediment from a well clogging the filter or valve screen

    Our repairReplace the filter, clean or replace the valve and test the fill

  3. You noticeIce maker arm down, bin empty

    Usual sourceThe module has failed, or the mold thermostat never signals that the ice is ready

    Our repairTest the module and replace it if it does not complete a harvest

  4. You noticeIce spills into the bin as a single sheet

    Usual sourceInlet valve sticking open and overfilling the mold

    Our repairReplace the valve and dry out the freezer

  5. You noticeFreezer cold enough but no ice and no water at the dispenser

    Usual sourceWater not reaching the fridge: a kinked line or a closed valve

    Our repairCheck the line and valve and replace damaged tubing

  6. You noticeWater puddling under a manufactured home's fridge

    Usual sourceCracked plastic supply line under the floor or behind the fridge

    Our repairShut off the supply, replace the line and check for floor damage

Cold crawlspaces, long lines and wells

In Sedro-Woolley's older houses, the water line to the fridge often climbs from a basement or crawlspace through the floor or along an exterior wall. During cold spells, that short stretch of thin tubing can freeze while the rest of the house stays warm, and the ice maker stops. Thawing it slowly usually brings the ice back, but tubing that has frozen more than once may crack. We find where the line runs and suggest insulating it or moving it to a warmer path before the next cold spell.

Manufactured homes, about 11.9% of the area's housing, tend to have long supply lines running under the floor to the kitchen. Those lines are exposed to cold air under the skirting and to rodents. A line that cracks below the floor can leak for a while before anyone notices, so any unexplained drop in ice production or a damp patch near the fridge is worth a look sooner rather than later. Rodents chew plastic tubing more readily than copper or braided line, which is one reason we may suggest a sturdier line for a run under the home.

On SR 9 properties with wells, sediment is the most frequent cause of weak ice production. The inlet valve's screen catches grit, and the valve opens but lets through too little water. A new refrigerator filter helps, but the valve screen usually needs cleaning or replacing as well, and a filter that does not seat properly can let sediment straight past it. We measure a timed fill into the fridge, which settles quickly whether the valve or the supply is to blame.

Testing a refrigerator dispenser and ice maker

How an ice maker repair on SR 9 gets priced

Prices stay off this page, since a module or inlet valve for one fridge can be priced far apart from one make to the next. We meter both, then put one price in writing before anything is replaced. Go ahead and the visit fee comes back off the repair, and it settles the visit on its own if you decline.

Pricing, explained

Six appliances, one file each

Tap a tab or let the folder turn on its own.

Empty upright freezer with wire shelves and door bins

File 1 of 6

Ice makers

Empty bins, thin hollow cubes, a fill line frozen in an outflow week: valve, line and module, tested in order.

Ice makers in Sedro-Woolley
1 / 6

When an ice maker repair pays off

Almost always, if the refrigerator around it is in good shape. An inlet valve, a supply line or an ice maker module is a modest repair compared with replacing the refrigerator, and the fridge often has many years left. The time to think twice is when the ice maker is one of several faults on an older fridge, or when the fridge has a sealed-system problem, which is work we do not do and which often makes replacement the better choice. Some households on wells decide the ice maker is not worth the upkeep and switch it off; that is a reasonable choice, and closing and capping the supply removes one more possible leak. Either way, we explain what we found and give you the repair price in writing first, so the choice is an informed one.

What callers ask us

My ice maker stopped during a cold snap. Is the line frozen?

Quite possibly, especially in an older home where the line runs through a crawlspace or an outside wall. Turn the ice maker off and let the house warm up. If ice returns within a day or two, the line was frozen; if it does not, or you see water, call us. We check the line for cracks and test the valve.

Why are my ice cubes gritty or cloudy?

On well water, sediment can pass through or around a worn filter and into the ice. Replace the refrigerator's water filter first. If the cubes stay cloudy or gritty, the inlet valve screen may be clogged, or the filter housing may not be sealing. We inspect and clean or replace the valve and check the filter seat.

Can you replace just the ice maker, not the whole fridge?

Yes. The ice maker module is a separate part on most refrigerators, and we carry common ones for Whirlpool, GE, Frigidaire, LG, KitchenAid and Maytag fridges. If your model needs a part we do not have with us, we order it and return. We test the valve and supply first, because a new module will not help if water is not reaching it.

Water is pooling near my fridge in a manufactured home. What should I do?

Turn off the water supply to the fridge, usually at a valve under the sink or under the home, and dry the area. The cause is often a cracked plastic supply line under the floor or behind the fridge. Book a visit, and we will find the leak, replace the line and check the inlet valve.

Do you cover Wickersham, Acme and Van Zandt for ice maker repairs?

Yes. We repair refrigerators and ice makers all along SR 9, and those addresses are on our regular routes. Go ahead and the visit fee comes back off the repair. Have the model number from inside the fresh-food side ready when you call (360) 525-9166 or book online.

Set up the visit

Call (360) 525-9166 or book online for ice maker repair in Sedro-Woolley or along SR 9.

From our repair notebook

Book a visit

Request a technician

Leave a few details and a dispatcher rings you back to agree on an arrival window. Someone picks up all week, and a request sent before mid-morning has the likeliest shot at a visit the same day.

  • The fee comes off any repair you go ahead with
  • Model number in the form so the right part rides along
  • A second machine? List it in the form and the technician checks it too

Prefer to talk? (360) 525-9166 · Calls daily 8–7

These details are used only to set up your visit. The diagnostic fee is named when we call back and is credited to any repair you approve.

State records

On file with Washington L&I

Both credentials are public state records. Tap a card for details, or look the numbers up yourself on L&I Verify.

Check our licenses yourself
CallBook a visit