Skip to content
LarchHVAC & Appliance · Bellingham (360) 525-9166 Book a visit

Gas & electric dryers

Dryer Repair in Bellingham & Whatcom County, WA

Dryer repair, gas and electric, Bellingham to Burlington

Laundry rarely dries on a line here for most of the year, so a dryer that won’t heat or needs three runs to finish is a real problem. We repair gas and electric dryers across Whatcom County and north Skagit, starting with the vent.

Electric dryer with the drum open during a repair
  • Fee named up fronton the phone, before anyone drives out
  • A price on papersigned off by you before parts come off
  • Border to the SkagitGlacier and Sumas on the same terms as town
  • Seven days, 8 to 7a morning call often means a visit today

Most dryer calls we take in Whatcom and north Skagit come down to airflow. Lint packs the duct, a foil connector gets flattened behind a stacked pair, or the outside flap sticks shut, and the heat builds up until a fuse or the high-limit trips for good. Wind adds to it: Fraser outflow gusts topped 50 mph in January 2024, and exposed wall hoods on the north county flats take a beating from storms like that. On the bay side, around Birch Bay, Blaine and Semiahmoo, salt air pits metal hoods and screws faster than it does inland. Long dry times also cost money on every load, which is why a vent problem is worth fixing even before anything breaks.

Fuel changes from one address to the next. Gas mains run in Bellingham, Ferndale, Lynden, Blaine, Everson, Sumas, Burlington and Sedro-Woolley but not in Kendall, Maple Falls or Glacier, so dryers up the Mount Baker Highway tend to be electric or propane. We work on both, including the compact and stacked models common in condos, rentals and manufactured homes. Stacked units in condos often vent through long ceiling runs, and those clog faster than a short duct through an outside wall. If a gas dryer ever smells of gas, don’t go looking for the cause: leave the house and call 911 or your gas utility from outside.

Dryer symptoms and their usual causes

  1. You noticeDrum turns, but the air stays cool (electric)

    Usual sourceOpen thermal fuse, burned heating element or failed high-limit, usually after a restricted vent

    Our repairWe test each part of the heat circuit, replace the failure, and check the vent so it doesn’t happen again

  2. You noticeGas dryer heats for a few minutes, then runs cold

    Usual sourceGas valve coils weakening, or an igniter or flame sensor near the end of its life

    Our repairWe watch the ignition sequence, test the coils and sensor, and replace whatever fails

  3. You noticeClothes still damp after a full cycle, or a vent warning on the display

    Usual sourceLint packed in the duct, a crushed transition hose, or a blocked hood outside

    Our repairMeasure the airflow at the hood, clear what we can reach, show you where the rest of the run is blocked

  4. You noticeThumping, squealing or scraping as the drum turns

    Usual sourceWorn drum rollers, idler pulley, belt or front glides

    Our repairWe open the cabinet and replace the worn rollers, pulley or belt, often as a set when they’ve worn together

  5. You noticeHums, or does nothing at all when you press start

    Usual sourceDoor switch, start switch, a broken belt, or a motor stopped by a thermal fuse

    Our repairWe trace the start circuit with a meter and fix the open part instead of swapping guesses

  6. You noticeBlank panel or odd cycling after an outage

    Usual sourceControl board or timer damaged by a surge when power returned

    Our repairWe confirm the dryer is getting proper voltage, then test the board before recommending a new one

How we work on dryers

On a dryer call we look at the vent before the dryer itself. A blocked run can burn out a new heating element within months, so we check the exhaust at the outside hood and the transition behind the machine, then open the cabinet to test the fuse, thermostats, element or gas valve. We repair Whirlpool, Maytag, GE, LG, Samsung, Kenmore, Electrolux, Frigidaire and Speed Queen dryers. LG models report vent trouble with their own flow codes, and Whirlpool-built dryers often stop dead when the thermal fuse opens, which is why the fuse is one of the parts that rides along with us. We also check the drum seals and the lint screen housing, because lint escaping inside the cabinet and settling near the heat source is how dryer fires start.

A dryer that stood in floodwater needs more care than one that simply quit. After the November 2021 floods in the Nooksack and Sumas lowlands, and again after December 2025, when the Skagit crested at a record and all of Burlington was ordered to evacuate, floodwater left silt in motors, corroded terminals and soaked control boards. We don’t restart a gas dryer that has been under water until the valve and burner have been checked, and we tell you plainly when the damage makes replacement the wiser spend. Dryers that escaped the water but live in damp, unheated garages show their own wear, mostly rust on the drum and cabinet, and we tell you whether it’s cosmetic or something that will cut the machine’s life short.

Dryer with the door open for inspection

Where the number on a dryer repair comes from

The fix usually turns out to be a thermal fuse, an igniter, an element, rollers or a board. One brand’s part can be priced far apart from one make to the next, so the technician meters the dryer and puts your repair total on paper before starting. Approve, and the diagnostic rolls into the repair; decline, and it is your whole bill. We cover Point Whitehorn to Van Zandt on our regular routes.

Pricing, explained

Six appliances, one file each

Tap a tab or let the folder turn on its own.

1 / 6

From our repair notebook

What callers ask us

How often does the dryer vent need cleaning?

Clean the lint screen every load; that part is on you. The duct itself depends on its length and route. A short, straight run to an outside wall can go a long time, while a long run through a condo ceiling or up through a roof clogs much faster. Longer dry times or a laundry room that gets warm and muggy mid-cycle point at the vent first.

Do you repair propane dryers?

Yes. Gas dryers run on natural gas or propane with the same kind of burner, igniter and valve, so the diagnosis is similar. Many homes along the Mount Baker Highway and in rural Skagit use propane from a tank. Should the dryer ever smell of gas, get out and ring 911 or the propane company before you ring us.

Can I keep running a dryer that smells hot?

Stop the cycle. A scorched smell usually points to lint gathering where it should not, in the duct or inside the cabinet by the heater. Clean the lint screen, check that the flap on the outside hood opens when the dryer runs, and don’t run it unattended until it has been looked at. We check both the vent and the cabinet on the same visit.

Can a dryer that sat in floodwater be repaired?

Sometimes, depending on how high the water came and how long it stayed. Leave it unplugged, and if it’s gas, keep the supply valve closed. We open it up to check the motor, board, wiring and, on gas units, the valve and burner assembly. If silt and corrosion have reached too many parts, we tell you so and you only pay the diagnostic.

Is a squealing dryer worth fixing?

Almost always. Squeals and thumps come from rollers, the idler pulley, the belt or the drum glides, which are wear parts on a machine whose motor and heater are often still fine. Replacing them brings a dryer back to quiet running. Waiting too long can let a worn roller wear into the drum or snap the belt, which turns a routine repair into a longer one.

Set up the visit

Call (360) 525-9166 or book online.

Book a visit

Request a technician

Leave a few details and a dispatcher rings you back to agree on an arrival window. Someone picks up all week, and a request sent before mid-morning has the likeliest shot at a visit the same day.

  • The fee comes off any repair you go ahead with
  • Model number in the form so the right part rides along
  • A second machine? List it in the form and the technician checks it too

Prefer to talk? (360) 525-9166 · Calls daily 8–7

These details are used only to set up your visit. The diagnostic fee is named when we call back and is credited to any repair you approve.

State records

On file with Washington L&I

Both credentials are public state records. Tap a card for details, or look the numbers up yourself on L&I Verify.

Check our licenses yourself
CallBook a visit