Skip to content
LarchHVAC & Appliance · Bellingham (360) 525-9166 Book a visit

Burlington · refrigerator ice makers

Ice Maker Repair in Burlington, WA

Ice maker repair in Burlington

An ice maker that quits is usually a supply line, a fill valve or the ice maker module itself. We sort out which on the first visit to your Burlington, Alger, Bow or Edison kitchen and write the price before any repair.

Common fix
Water inlet valve or ice maker module, both carried on the van.
Water
Public water in town; Bow and Edison homes often use wells.
Drive
About 22–28 minutes from downtown Bellingham.
Testing a refrigerator dispenser and ice maker
  • Fee named up fronton the phone, before anyone drives out
  • A price on papersigned off by you before parts come off
  • Border to the SkagitGlacier and Sumas on the same terms as town
  • Seven days, 8 to 7a morning call often means a visit today

In Burlington's apartments and townhomes, the ice maker sits inside a fridge that someone shoves back into a tight alcove after cleaning, and that shove is often where the trouble starts. The thin supply tube behind the fridge kinks or cracks, the water flow drops, and the ice maker turns out small, hollow cubes or nothing at all. In houses around town and out toward Bow and Edison, the fridge ice maker is joined now and then by a dispenser in the door that grinds or jams. Ice makers in garage fridges on the farms around Edison face another enemy: a cold garage that freezes the supply line.

An ice maker is a short chain: shutoff valve, supply line, water filter, inlet valve, fill tube, the ice maker module and its ejector, then the bin, the auger and the dispenser. We test each link in order, so we replace only the part that failed. We carry the common inlet valves and modules for Whirlpool, GE, Frigidaire, LG and KitchenAid refrigerators, and if the freezer itself is running too warm to make ice, we diagnose that on the same visit.

Ice maker problems in Burlington homes

  1. You noticeNo ice at all, though the fridge cools normally

    Usual sourceWater not reaching the mold: closed shutoff, kinked line or failed inlet valve

    Our repairCheck the supply, test the valve and replace the part that blocks the flow

  2. You noticeSmall, hollow or clumped cubes

    Usual sourceLow water pressure, a clogged filter or a weak inlet valve

    Our repairMeasure the flow, replace the filter or valve and adjust the fill

  3. You noticeIce maker fills but never dumps

    Usual sourceEjector motor or module failure, or a mold heater that does not warm

    Our repairTest the module and replace it if the cycle stalls

  4. You noticeIce frozen solid in the fill tube

    Usual sourceFreezer running too cold, or a drip from a failing valve

    Our repairThaw the tube, find the source of the drip and replace the valve if it leaks

  5. You noticeWater on the floor behind the fridge

    Usual sourceCracked plastic supply line or a loose fitting at the valve

    Our repairShut off the supply, replace the line and fitting and check for damage

  6. You noticeDispenser chute clogged or auger grinding

    Usual sourceIce melted and refroze in the bin, or a worn auger motor

    Our repairClear the chute and bin, test the auger motor and replace it if needed

Why Burlington ice makers stop

Rentals see the kinked-line problem most. When a tenant moves out, the fridge is pulled forward for cleaning, and the plastic tube behind it gets crushed or tugged off its fitting when it goes back. The ice maker carries on calling for water that never arrives, the inlet valve hums against nothing, and eventually the module stops trying. We replace the line with a sturdier one where it makes sense. In buildings where the water to every unit is shut off for maintenance, an ice maker that ran dry for a few days can also come back with a sticking valve.

December 2025 left its own problems. Fridges that sat without power through the evacuation often had water left in the fill tube and the mold, and when the power came back that water froze into a plug. Others drew silty water once the supply was restored, which can clog the filter and the inlet valve screen. If your ice maker has not worked right since the flood, we start with the filter and the valve, then move on to the module.

Homes on wells around Bow, Edison and Alger have their own pattern. Well pressure rises and falls with the pump cycle, and a weak inlet valve may not fill the mold fully when pressure is low. Fine sediment also builds up in the valve screen. Both are worth checking before you replace an ice maker module that might be fine. If your pressure tank's gauge drops low between pump cycles, mention it when you book.

French-door refrigerator open for a repair check

Burlington ice maker repair: metered, then priced in writing

We keep prices off this page because an inlet valve or ice module for one refrigerator brand may cost several times what it does for another. We meter the valve and module first, then write one price; nothing is replaced until you approve it. Approving the repair puts the visit fee inside it.

Pricing, explained

Six appliances, one file each

Tap a tab or let the folder turn on its own.

French-door refrigerator open for a repair check

File 1 of 6

Ice makers

Empty bins, thin hollow cubes, a fill line frozen in an outflow week: valve, line and module, tested in order.

Ice makers in Burlington
1 / 6

Fix the ice maker or do without?

Most ice maker repairs are worth doing: an inlet valve, a supply line or an ice maker module cost far less than a new refrigerator, and the fridge around them usually has plenty of life left. Where we suggest weighing it up is on an older fridge whose ice maker is one of several problems, for example a fridge that also has a failing defrost system or door seals that no longer close, or on a unit that sat in floodwater. Some Burlington owners of rental units simply switch the ice maker off and close its supply, which is a sound choice when nobody uses it and removes one more thing that can leak between tenants. We will tell you what a repair costs in writing and whether we see other problems coming, so the call is yours with the full picture in front of you.

What callers ask us

Why does my ice maker make tiny, hollow cubes?

Not enough water is reaching the mold in each cycle. The usual causes are a clogged water filter, a kinked supply line behind the fridge, a partly closed shutoff valve or an inlet valve that has weakened. Start by replacing the filter if it is overdue. If the cubes stay small, we test the flow and the valve and fix the restriction.

My ice maker stopped after the power went out during the evacuation. Is it broken?

Not necessarily. Water left in the fill tube often freezes into a plug after a long outage, and the ice maker then calls for water that cannot get through. Turning the ice maker off and letting the fill tube thaw sometimes clears it. If ice still does not come within a day, the valve or module may have failed, and we can test both.

Do you repair the ice maker in any brand of refrigerator?

We work on ice makers in Whirlpool, GE, Frigidaire, LG, KitchenAid, Maytag, Kenmore and many other refrigerators. Give us the model number off the fresh-food label when you book, either on the phone or in the online form, so we can bring the right valve or module along on the first visit.

Is a leak behind the fridge from the ice maker line?

Often. The plastic supply line behind many fridges cracks with age or gets crushed when the fridge is pushed back. Shut the water off at the valve under the sink or behind the fridge, wipe up the water and book a visit. We replace the line and fitting, check the inlet valve and look for water damage under the fridge.

Can I just turn the ice maker off instead?

Yes. If nobody in the house uses ice, switching the ice maker off and closing the supply valve is perfectly reasonable, and it removes a possible leak. Make sure the arm or switch is off so the valve does not keep trying to fill. If you change your mind later, we can test and repair it then.

Set up the visit

Call (360) 525-9166 or book online to get your Burlington ice maker working again.

From our repair notebook

Book a visit

Request a technician

Leave a few details and a dispatcher rings you back to agree on an arrival window. Someone picks up all week, and a request sent before mid-morning has the likeliest shot at a visit the same day.

  • The fee comes off any repair you go ahead with
  • Model number in the form so the right part rides along
  • A second machine? List it in the form and the technician checks it too

Prefer to talk? (360) 525-9166 · Calls daily 8–7

These details are used only to set up your visit. The diagnostic fee is named when we call back and is credited to any repair you approve.

State records

On file with Washington L&I

Both credentials are public state records. Tap a card for details, or look the numbers up yourself on L&I Verify.

Check our licenses yourself
CallBook a visit